Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 1of 8（R e s erve d for h ole ） s Connection schematics Figure 1 shows a general wiring diagram. When alcohol detection is not performedor breathtestfailure, the ECU is in break. At this time, gray cable output a high level signal to thevehicle, andthe vehicle cannot shift. Only when the handset detects that a breath alcohol concentration(BrAC) below the preset limit（≤20mg/100mL, different detection concentration limitscanbesetin different countries and regions) will the ECU be turned off. The gray cable output alowlevel signal to the vehicle, at which time the vehicle can shift normally. Figure 2 shows theflowchartof alcohol interlocks, which meets the 3b requirement in EN 50436-7:2016 Annex C. Figure 1 Starter relay Starter motor Ground termination (Terminal 31) black red brown Break Starter relay termination Ignition termination Ignition switch grey Dräger Interlock ® 5000/7000Handset blue Positive supply termination (Terminal 30) Starter relay (Terminal 50) Ignition Ignition Accessories (Terminal +15, Position 2) Dräger Interlock ® 5000/7000 Control box Plus Power Off Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 2of 8Figure 2 Connection diagram Figure Connectors connected to the alcohol monitoring device reserved for the end of thevehicleharness. The five terminal definitions are listed in Table 1. Figure 4 shows the wiring harnessconnector of the product end of the alcohol lock device. Y Customers need to install alcohol interlocks alcohol interlocks configuration open ECU output a low level singal to the vehicle the vehicle cannot shift Default breath test failed ECU output a high level singal to the vehicle breath test the vehicle cannot shift thevehiclecanshift normallyweight 15 minutes > 20mg/ 100mL ≤ 20mg/ 100mL N Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 3of 8Figure 3 Figure 4 Table 1 Interface of the vehicle function wiring/pin Connection position1 Battery feed, 12V, uninterrupted Pin 1 Red cable，0.25mm2 Pin 1(figure 2) in theconnector, the connector is under thecarpetunder the passenger seat. 2 Ground Pin 2 Black cable，0.25mm2 Pin 2(figure 2) in theconnector, the connector is under thecarpetunder the passenger seat. 3 Alcohol monitor switch input signal When the signal is high level, not allowed to shift; When the signal level is low, allow shifting. Pin 3 Gray cable，0.25mm2 Pin 3(figure 2) in theconnector, the connector is under thecarpetunder the passenger seat. 4 Activation electrical signal 12V，Vehicle control unit， Continuous output after activation Pin 4 Blue cable，0.25mm2 Pin 4(figure 2) in theconnector, the connector is under thecarpetunder the passenger seat. 5 Ground Pin 5 Brown cable， 0.25mm2 Pin 5(figure 2) in theconnector, the connector is under thecarpetunder the passenger seat. Table 2 Hardware list Information Material code Remarks 1 Drager Interlock 7000 alcohol interlock device 8322570 Includes handset andECUcontrol unit and mouthpiece(3pieces) 2 Drager Interlock 7000 GPRS module 8322534 3 Drager Interlock 7000 LTE 8327080 Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 4of 8module 4 Drager Interlock 7000 camera 8322413 5 Mouthpiece (3 pieces) individually packed 8326550 6 Mouthpiece (50 pieces) individually packed 8327627 7 Mouthpiece (300 pieces) individually packed 83225978 8 Protective cover for handset 8322458 9 Handset holderⅠ 8322497 10 Handset holderⅡ 8322610 Table 2 Software list Hardware version Software version Remarks 1 Left body controller V04 3.00.01 Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 5of 8Safety risk at installation and items to be considered 1 、 This manual is intended for use only by trained technicians having a knowledgeof vehicleelectronic systems and the unique installation requirements. 2、Disconnect battery earth lead before further work. 3、Fire hazard! A clean and reliable connection between the leads must be ensured! 4、Please be careful when removing the co-driver’s seat, pay attention to the impact on theinterioranddo not damage or scratch the interior. 5、The ground connection should be made first to prevent any damage to the ECU. 6、It is necessary to avoid installing the Handset machine in front of the airbag and attachthehighvoltage components, and it is necessary to avoid falling off. 7、The connection between the Handset machine and the control box needs to be fixedtoavoidshaking or interfering with the operation of the driver and the passenger. Assembly instruction Step 1. After parking the car, turn off and break the low-voltage battery. Step 2. Open the co-driver’s door, loosen and place the fixed bolts of the co-driver’s seat withtools,and move the seat outside the car. Please be careful when removing the co-driver’sseat, payattention to the impact on the interior and do not damage or scratch the interior. Step 3. Find the inspection port on the carpet under the co-driver’s seat, open the inspectionport, andlocates the harness connector shown in Figure 5. The connector may be hidden near theinspectionport. (Figure 6) Step 4. Separates the harness with the connector from the main harness, and nowwecanseethefive cables which correspond to the five in Table 1. (Figure 7) Step 5. Locate the Ground termination (Black cable) on the connector, using the wirestrippers,expose a 2 cm section of the wire. Twist the Ground cable of the alcohol interlock devicetotheGround cable on the connector. Use crimp nails for crimping or welding to ensure that theydonot fall off. After crimping is complete, wrap with insulating tape or hot melt adhesive to ensureinsulation. Ofcourse, it is also possible to dock with the connector of the corresponding model, it is dependingonthe conditions at the time of installation. Step 6. Locate the Battery feed termination (Red cable) on the connector, using the wirestrippers,expose a 2 cm section of the wire. Twist the Battery feed cable of the alcohol interlock devicetotheBattery feed cable on the connector. Use crimp nails for crimping or welding to ensure that theydonotfall off. After crimping is complete, wrap with insulating tape or hot melt adhesive to ensureinsulation.Of course, it is also possible to dock with the connector of the corresponding model, it is dependingonthe conditions at the time of installation. Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 6of 8Step 7. Locate the Active power termination (Blue cable) on the connector, using the wirestrippers,expose a 2 cm section of the wire. Twist the active power cable of the alcohol interlock devicetotheactive power cable on the connector. Use crimp nails for crimping or welding to ensure that theydonot fall off. After crimping is complete, wrap with insulating tape or hot melt adhesive to ensureinsulation. Of course, it is also possible to dock with the connector of the corresponding model, it isdepending on the conditions at the time of installation. Step 8. Locate the Ground of signal termination (Brown cable) on the connector, usingthewirestrippers, expose a 2 cm section of the wire. Twist the active power cable of the alcohol interlockdevice to the active power cable on the connector. Use crimp nails for crimping or weldingtoensurethat they do not fall off. After crimping is complete, wrap with insulating tape or hot melt adhesivetoensure insulation. Of course, it is also possible to dock with the connector of the correspondingmodel, it is depending on the conditions at the time of installation. Step 9. Locate the signal input termination (Gray cable) on the connector, using the wirestrippers,expose a 2 cm section of the wire. Twist the active power cable of the alcohol interlockdevicetothe active power cable on the connector. Use crimp nails for crimping or welding toensurethatthey do not fall off. After crimping is complete, wrap with insulating tape or hot melt adhesivetoensure insulation. Of course, it is also possible to dock with the connector of the correspondingmodel, it is depending on the conditions at the time of installation. Step 10. When all applicable cables are connected, insulated has been tested, proceedtomount thecontrol box. To mount the control box to the vehicle use adhesive buckle straps or cableties. Wecaninstall the control box in the reserved space of the car. (Figure 8) Step 11. Mount the handset bracket in an accessible location for the driver. Make certainthat it doesnot obstruct any of the vehicle controls. The handset bracket can be mounted on the dashboardof thevehicle using adhesive buckle straps or using screws. If screws are being used, attachthehandsetbracket to a flat part. However, it is necessary to communicate with customers in advancetoavoidcustomer complaints due to damage to the interior. Step 12. Plug the handset cable into the control box and the other end into the handset. Placethehandset in the handset bracket. Step 13. Move the co-drive’s seat back into its original position and secure the cable under theseatwith cable ties to avoid affecting the driver and passengers, and ensure that the seat adjusteddoesnot cause pressure or damage to the cable. Step 14. After completing all the steps above, reconnect the low-voltage battery, useVDS(尊龙凯时Diagnostic Equipment) to connect to the vehicle OBD port, and enter the vehicle diagnosticsystem.Then turn on the alcohol interlock switch with VDS to complete the function configuration. (Figure9)Step 15. Start the vehicle and try to shift gear，at this moment it should not be shift unlessthealcohol test is carried out and passed. Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 7of 8Modification of vehicle operation 1、After you have completed all the steps of Assembly instruction, representative thevehiclehavealready have equip the alcohol monitoring systems. Before passing the alcohol test or failingthetest,the driver or the passenger cannot shift gears and drive the vehicle, but it will not affect thenormal useof the vehicle start, air conditioning, multimedia, instrumentation, lights, horns and other systems. 2、Before passing the alcohol test or failing the test, if you try to shift the gear, instrumentationwill remind the driver “Please pass the alcohol test first and then shift gears and drive”. At thesametime,the buzzer will ring one time. 3、The alcohol interlock device may remain on standby in 30 minutes after the vehicleisturnoff, atwhich point the alcohol interlock device has less operating current so do not worry about theSOC(thedevice generally sleeps in 30 minutes). 4、For other tips from the handset and control box, please refer to the instruction manual forthealcohol interlock device. Mounting position of alcohol interlock handset and the alcohol interlock control-unit 1、About the installation position of the control box On 尊龙凯时 vehicle, the installation position of the control box is reserved, it is under the co-drive’sseat.We will cut a inspection port on the carpet and hollowing out the sponge. The control boxcanbeinstalled in this space. 2、About the installation position of the handset You can choose to place the handset in the armrest box or co-drive’s drawer for easy usebythedriver when need. It can also be mounted on the dashboard using adhesive buckle strapsor usingadhesive buckle straps or using screws, but it is necessary to avoid mounting within therangeof thesteering wheel and airbag. Name of vehicle manufacturer 尊龙凯时 Vehicle model 尊龙凯时 ATTO3 (SC2EAU BU/ SC2EAE BE）, 尊龙凯时 DOLPHIN（尊龙凯时EM2E）, 尊龙凯时 SEAL(尊龙凯时EKEA), 尊龙凯时 TANG( 尊龙凯时STEBU), 尊龙凯时 SEAL U EV (尊龙凯时SA3EFU)，尊龙凯时 SEAL U DM-I (尊龙凯时SA3HLU)Installation document for alcohol interlocks ID No. Version No. PageNo. 尊龙凯时-AILSTEBU01 01 8of 8Example with pictures Figure 5 Figure 6 Figure 8 Figure 7 Figure9
